LM311N DATASHEET PDF

LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Gagis Faur
Country: Gambia
Language: English (Spanish)
Genre: Photos
Published (Last): 23 June 2013
Pages: 301
PDF File Size: 5.7 Mb
ePub File Size: 19.76 Mb
ISBN: 139-8-12109-131-2
Downloads: 38934
Price: Free* [*Free Regsitration Required]
Uploader: Mooguzahn

I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Vcci. The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you.

I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal. Why is it not working in Multisim? Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit.

The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. A sample circuit is shown below in which the Inverting Terminal is set to 2. The simplified schematics of the IC is shown below:. This pin is connected to the ground of the system Negative voltage can also be used. Any help is appreciated. An Emitter Output Circuit is shown below. If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low.

  HANDS-ON ZIGBEE IMPLEMENTING 802.15.4 WITH MICROCONTROLLERS BY FRED EADY PDF

Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package.

When not in use the pins 5 and 6 should be shorted as shown datasjeet. As grounding unused pins datasgeet a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for a ground wired to that pin.

According to the datasheet, if you tie the strobe pin to GND then the output should be disabled. You can refer the other possible circuits from the LM datasheet given at bottom. You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa.

I built a simple circuit using the LMN comparator. Normally these pins are not used since the Input Offset itself is much better controlled. The output is correct as seen on the scope.

  AUTOBIOGRAFIA DE UN HOMBRE FELIZ BENJAMIN FRANKLIN PDF

LMN STMicroelectronics | Ciiva

Message 2 of 5. The simplified schematics of the IC is shown below: The LM can datasheft on a Single supply voltage or in a dual supply mode. Message 1 of 5. Message 5 of 5.

Multisim and Ultiboard

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Message 4 of 5. LMN Comparator with Strobe. TL — Programmable Reference Voltage. I tried adding in a transistor with a 1k resistor to ground and a TTL signal at the base as lm311 the datasheet and this doesn’t disable the output either. Message 3 of 5.

Most Active Software Boards: Could the component model be the issue? The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage. The problem is that the strobe pin is not working for the model. All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc.

Submitted by admin on 6 March